How to Stabilize Towels for Machine Embroidery
EmbroideryGo · 11/8/2026 · 8 min read
Article map

# How to Stabilize Towels for Machine Embroidery
Embroidering on towels is one of the most rewarding projects you can tackle with your machine, but the loopy terry cloth surface creates real challenges that flat woven fabrics simply do not. The loops stretch, the needle can push them aside, and the finished design can look sunken or distorted if you skip the right preparation steps.
The good news is that stabilizing towels correctly is a learnable skill, and once you understand why each step matters, you will get clean, professional results every time. This guide walks you through the entire process, from choosing your stabilizer to finishing the back of the hoop, so your monograms, logos, and decorative motifs land exactly where you want them.
Understanding Why Towels Are Difficult to Embroider
Terry cloth is woven with intentional loops on the surface, and those loops are the enemy of a crisp embroidery design. When the presser foot moves across the fabric, the loops shift. When the needle penetrates, it can catch a loop and drag it into the design area. The result is a fuzzy, uneven finish that obscures the stitching underneath.
Beyond the loops, towels are also thick and stretchy. The combination of weight and stretch means the fabric can pull away from the hoop during stitching, causing registration errors where one part of the design no longer lines up with another. A monogram that looks perfect in your software can arrive on the finished towel looking slightly off-center or wavy if the fabric was not locked down properly.
Understanding these two problems — loop interference and fabric movement — is the foundation of every stabilizing decision you will make. Every product and technique in this guide addresses one or both of those issues.
Choosing the Right Stabilizer
The most reliable choice for towels is a cutaway stabilizer in a medium weight, typically around 2.5 ounces. Cutaway stabilizers remain permanently attached to the back of the design after stitching, which is important because terry cloth is stretchy and a tearaway stabilizer would not provide enough long-term support. The design would distort the first time the towel went through a wash cycle.
For most standard bath towels and hand towels, a single layer of medium-weight cutaway is sufficient. For very thick or heavy-weight towels, you can use two layers. Place them together in the hoop as if they were one piece. Do not try to compensate for a thin stabilizer by adding more layers of tearaway on top of cutaway; the materials behave differently and the combination can create bulk without adding real stability.
Some embroiderers also use a water-soluble topping, which is a separate product from the stabilizer and serves a completely different purpose. The topping goes on top of the towel, not underneath it, and it is addressed in its own section below.
Hooping the Towel Correctly
Hooping a towel is different from hooping a flat woven fabric. You should never hoop the towel tightly in the traditional sense, because forcing thick terry cloth into a tight hoop can crush the loops and leave a permanent hoop mark around your design.
Instead, hoop only the stabilizer tightly. Place the inner ring of your hoop on a flat surface, lay the cutaway stabilizer over it, and press the outer ring down firmly so the stabilizer is drum-tight. Then lay the towel on top of the stabilizer and use temporary adhesive spray to bond the two together. This technique is called floating, and it keeps the towel flat against the stabilizer without compressing the terry loops.
Spray the adhesive onto the stabilizer, not onto the towel. Let it become slightly tacky for about fifteen seconds before pressing the towel down. Smooth the towel from the center outward to eliminate any bubbles or wrinkles. Once the towel is adhered, you can attach the hoop to your machine and begin stitching.
Using a Water-Soluble Topping
A water-soluble topping, sometimes called a wash-away topping or solvy, is a thin film that you lay over the surface of the towel before stitching. The needle stitches right through it, and when the embroidery is finished, you tear away the excess and dissolve the remainder in water.
The topping serves one critical purpose: it prevents the terry loops from poking up through the stitches and obscuring the design. Without it, the loops push between the threads and make the embroidery look fuzzy. With it, the stitches sit cleanly on top of a flat surface and the loops are held down during stitching.
Cut a piece of topping slightly larger than your design area and lay it over the hooped towel. You do not need to hoop it separately; it simply rests on the surface. Some embroiderers use a small piece of tape at the edges to keep it from shifting before the first stitches lock it in place. After stitching, tear away as much of the topping as you can by hand, then rinse the towel in warm water to dissolve the rest.
Selecting the Right Design and Format
Not every embroidery design works equally well on towels. Designs with very fine details, thin lettering, or dense fills can look muddy on terry cloth because the surface texture adds visual noise. Bold designs with clear outlines and open fill areas tend to read much better.
When you browse embroidery designs at EmbroideryGo, look for files that are specifically digitized for terry cloth or described as suitable for textured fabrics. These designs typically have underlay stitches built in to flatten the loops before the top stitching runs. Good underlay is one of the most important factors in towel embroidery, and it is something the digitizer handles in the file itself.
Make sure you download the format that matches your machine. Common formats include DST for Tajima and many commercial machines, PES for Brother, JEF for Janome, HUS and SEW for Husqvarna Viking, and EXP for Melco. Pfaff machines typically use JEF or a proprietary format depending on the model. If you are unsure which format your machine reads, check your manual or visit the EmbroideryGo help center for guidance.
Needle and Thread Recommendations
Use a sharp embroidery needle in size 75/11 or 80/12 for most towels. A sharp needle penetrates the terry loops cleanly rather than pushing them aside. Ballpoint needles, which are designed for knits, are not the right choice here because they are designed to slide between fibers rather than pierce through them.
For thread, 40-weight polyester or rayon embroidery thread works well on towels. Polyester is the more practical choice for items that will be washed frequently because it is colorfast and resistant to chlorine bleach. Rayon has a slightly higher sheen but is more delicate in the wash.
Here is a quick checklist of supplies to gather before you begin:
- Medium-weight cutaway stabilizer (at least one sheet per design)
- Temporary adhesive spray
- Water-soluble topping film
- Sharp embroidery needle, size 75/11 or 80/12
- 40-weight polyester embroidery thread
- Small scissors for trimming stabilizer after stitching
- A lint roller to clean the towel surface before hooping
Testing Before You Stitch the Final Towel
Always run a test stitch on a scrap piece of terry cloth before committing to the actual towel. Use the same stabilizer setup, the same topping, and the same needle and thread you plan to use on the final project. A test run takes only a few minutes and can save you from ruining an expensive towel.
Pay attention to how the design looks after you remove the topping and rinse the test piece. Check that the letters or shapes are crisp, that the underlay has flattened the loops effectively, and that the design has not shifted during stitching. If you see problems, adjust your stabilizer weight or your hooping technique before moving on.
Machine embroidery has a long history of adaptation to different fabric types, and towels are simply one more surface that rewards careful preparation. Manufacturers like Tajima have built machines capable of handling thick substrates precisely because demand for embroidered towels in hospitality, sports, and home décor is so strong.
Finishing and Caring for Embroidered Towels
After stitching, trim the cutaway stabilizer close to the design edges on the back of the towel, leaving about a quarter inch of stabilizer around the perimeter of the stitched area. Do not trim all the way to the stitches, because the stabilizer needs to remain attached to support the design through washing.
Rinse the towel in warm water to dissolve any remaining topping, then wash it according to the towel manufacturer's care instructions. Turn the towel inside out before machine washing to protect the embroidery from abrasion. Tumble dry on a low heat setting.
For more tips on working with different fabric types and troubleshooting common problems, visit the EmbroideryGo blog, where new articles are published regularly to help you get the most from your machine and your design files.



