How to use a topping stabilizer on terry cloth and fleece
EmbroideryGo · 11/7/2026 · 7 min read
Article map

# How to Use a Topping Stabilizer on Terry Cloth and Fleece
Embroidering on terry cloth towels and fleece jackets is one of the most rewarding things you can do with a home or commercial embroidery machine. The results look professional, the finished items make excellent gifts, and the fabrics are widely available. The challenge is that both materials have a raised, loopy surface that can swallow your stitches whole if you do not take the right precautions.
That is where a topping stabilizer comes in. Also called a water-soluble topping or WST, this thin film sits on top of your fabric during stitching and gives the needle a firm surface to punch through. Once the embroidery is done, you remove the topping and your design sits cleanly on top of the loops rather than sinking into them. The seven sections below walk you through every step of the process, from choosing your materials to finishing the piece.
Understanding Why Terry Cloth and Fleece Need a Topping
Terry cloth is woven with tiny loops of thread that stand up from the base fabric. Those loops are exactly what makes a towel absorbent, but they are also exactly what causes embroidery stitches to disappear. When a needle pushes thread down into a field of loops, the loops spring back up around the stitches and hide them. Letters become illegible, fine details blur, and satin columns look uneven.
Fleece has a similar problem. The brushed surface of fleece is made of tiny fibers that stand upright, and those fibers push between stitches as the machine runs. The result is a fuzzy, indistinct design that does not reflect the quality of the original file.
A water-soluble topping holds those loops and fibers flat during stitching. The needle perforates the topping film, the thread locks into place, and when you dissolve or tear away the topping afterward, the stitches are already anchored above the fabric surface where they belong. Machine embroidery on textured fabrics has been practiced for decades, and the topping method remains the most reliable solution professionals and hobbyists use today.
Choosing the Right Topping Stabilizer
Water-soluble toppings come in several weights. A lightweight film works well on fleece because fleece fibers are relatively fine. Terry cloth, especially thick bath towels, benefits from a medium-weight or heavy-weight topping because the loops are taller and more aggressive.
Look for a topping that is clear or lightly tinted so you can see your design placement through it. Avoid toppings that feel stiff or crinkle loudly, as these can cause the presser foot to drag and shift the fabric. A good topping tears cleanly after stitching without leaving ragged edges caught in the design.
If you are unsure which weight to start with, check the EmbroideryGo help center for guidance on matching stabilizers to fabric types. Having two or three weights on hand lets you experiment and find what works best for your specific machine and materials.
Selecting and Preparing Your Design
Not every embroidery design performs equally well on textured fabrics. Designs with very fine details, hairline lettering, or large areas of light fill stitching can still look muddy even with a topping. Choose designs that have bold outlines, well-defined satin columns, and lettering that is at least a quarter inch tall.
Browse the embroidery designs at EmbroideryGo and filter for designs described as suitable for towels, robes, or textured fabrics. These files are typically digitized with a slightly higher density and underlay stitching that compensates for fabric give.
Once you have your file, load it into your machine in the correct format. Common formats include DST, PES, JEF, EXP, HUS, and SEW. Machines from Brother typically use PES, Janome uses JEF, Pfaff uses HUS or EXP, and commercial Tajima machines use DST. Always confirm the format your machine requires before purchasing or transferring a file.
Hooping Terry Cloth and Fleece Correctly
Hooping is where many beginners run into trouble. Terry cloth and fleece both have stretch and bulk, and a poorly hooped piece will shift during stitching and ruin the registration of your design.
Use a hoop that is only slightly larger than your design. A hoop that is too large gives the fabric room to move. Tighten the outer ring firmly but stop before you distort the fabric. If the fabric is pulling or puckering inside the hoop, loosen it and re-hoop.
For terry cloth, place a layer of cutaway or tearaway stabilizer in the bottom of the hoop before adding the fabric. This backing stabilizer supports the base of the towel and prevents the loops from pulling the stitches downward. Fleece usually does well with a medium-weight tearaway or a single layer of cutaway, depending on how much stretch the fleece has.
Once the fabric and backing are hooped, lay your topping film over the top of the fabric inside the hoop. You do not need to hoop the topping itself. Simply hold it flat against the fabric surface with a few small pieces of temporary adhesive spray or a couple of straight pins placed outside the design area.
Setting Up Your Machine
Before you start stitching, make a few adjustments to your machine settings. Reduce your machine speed to about seventy percent of its maximum. Slower stitching gives the needle more time to penetrate the topping and fabric cleanly and reduces the chance of the topping tearing prematurely.
Check your needle. A sharp embroidery needle in size 75/11 works well for lightweight fleece. For thick terry cloth, move up to an 80/12 or 90/14. A dull or wrong-size needle will push loops aside rather than piercing cleanly through them.
Thread tension may need a slight adjustment. If you see bobbin thread pulling to the top of the design, loosen the upper tension by a small increment. Run a test on a scrap piece of the same fabric before committing to your final item.
Tajima commercial machines, such as those in the Tajima product lineup, often have built-in settings for thick fabrics. If you are using a commercial machine, consult its manual for recommended presser foot height adjustments when working with terry cloth.
Stitching the Design
Attach the hoop to your machine and center the design using the machine's preview or trace function. Watch the needle trace the outer boundary of the design to confirm it will land where you want it on the fabric.
Start the machine and monitor the first few stitches closely. The topping should remain flat and the needle should pierce it cleanly. If the topping bunches or the fabric shifts, stop immediately, re-hoop, and check your setup.
Here are the most common problems to watch for during stitching and how to address them:
- Topping tearing too early: Switch to a heavier-weight topping or reduce machine speed further.
- Stitches sinking into loops: Add a second layer of topping or increase the underlay density in your digitizing software.
- Thread breaking frequently: Check needle size, reduce speed, and confirm thread is feeding smoothly from the spool.
- Design shifting mid-stitch: Re-hoop more firmly and add a layer of backing stabilizer.
- Puckering around the design: Reduce upper thread tension slightly and ensure the hoop is not over-tightened.
Removing the Topping and Finishing the Piece
Once stitching is complete, remove the hoop from the machine. Tear away the bulk of the topping by pulling it gently from the edges of the design inward. Most water-soluble toppings tear cleanly along the stitch lines.
For any topping that remains caught in the stitches, dampen a clean cloth with warm water and dab the area. The film will dissolve within a few seconds. Do not soak the entire item unless it is colorfast and you intend to wash it anyway.
Trim any jump threads on the back with small scissors. If you used a tearaway backing, remove it carefully by scoring it close to the stitching and pulling it away in small sections. Cutaway backing should be trimmed to within a quarter inch of the design edge.
For more tips on finishing embroidered items and caring for different fabric types, visit the EmbroideryGo blog, where new articles are published regularly on techniques for home and commercial embroiderers alike.
With the right topping, the right design, and a little patience during setup, terry cloth and fleece become some of the most satisfying fabrics you will ever embroider. The results are durable, professional, and well worth the extra preparation time.



