How to use underlay stitches for cleaner embroidery
EmbroideryGo · 11/5/2026 · 7 min read
Article map

# How to Use Underlay Stitches for Cleaner Embroidery
If you have ever finished an embroidery project only to find that the top stitches look uneven, the fabric has puckered underneath, or the design seems to sink into a fluffy fleece, underlay stitches are almost certainly the missing piece. Underlay is the foundation layer of stitching that goes down before the visible design, and getting it right makes a dramatic difference to the finished result.
This guide walks you through the main types of underlay, when to use each one, and how to adjust settings in your software so that every design you stitch — whether you downloaded it from EmbroideryGo's design library or digitized it yourself — comes out looking sharp and professional.
What Underlay Actually Does
Underlay stitches serve three distinct purposes at once. First, they tack the fabric to the stabilizer so that the material cannot shift while the machine is running. Second, they compress or raise the fabric surface so that the top stitches have a consistent base to land on. Third, they create a slight tension across the design area that prevents the final satin or fill stitches from sinking into the weave of the fabric.
Without underlay, thread tension pulls the fabric inward with every stitch, causing the dreaded puckering effect that no amount of pressing will fully remove. Think of underlay as the primer coat before painting — skipping it saves a little time upfront but costs you quality at the end.
The Main Types of Underlay Stitches
Understanding the vocabulary helps you make better decisions in your digitizing software. The four types you will encounter most often are:
- Run stitch underlay — a single line of running stitches that traces the edge or center of a shape; lightweight and used for thin columns or lettering.
- Zigzag underlay — a zigzag pattern that runs across the fill area; good for medium-weight fabrics and satin stitch columns.
- Edge walk underlay — stitches that follow the perimeter of a shape just inside the border; helps define edges and prevents satin stitches from rolling off the edge.
- Tatami or fill underlay — a low-density fill pattern placed at a different angle from the top fill; ideal for large areas on stretchy or textured fabrics.
- Double zigzag underlay — two layers of zigzag crossing each other; used for very dense fills or thick fabrics like toweling.
- Center run underlay — a single run down the middle of a narrow column; the most common choice for lettering below 6 mm in height.
- Combination underlay — edge walk plus zigzag or fill, applied together; used for challenging fabrics or large bold shapes.
Choosing Underlay for Different Fabric Types
Stable woven fabrics like cotton twill or denim need relatively light underlay because the weave itself resists distortion. A single edge walk or a light zigzag is usually enough for satin columns, and a low-density tatami underlay works well for filled areas.
Stretchy fabrics such as knit polo shirts or athletic wear need more aggressive underlay because the material wants to move. A double zigzag or a combination of edge walk plus fill underlay locks the fabric down before the top stitches arrive. Always pair this with a cutaway stabilizer rather than a tearaway when working on stretch fabrics.
Textured surfaces like fleece, terry cloth, or velvet present a different problem: the pile pushes the top stitches upward and apart, making fills look sparse. A dense tatami underlay at 45 degrees to the top fill angle compresses the pile and gives the satin or fill stitches a firm platform. Tajima machines — you can explore their lineup at tajima.com — include built-in underlay controls that make adjusting density straightforward from the machine panel itself.
Underlay Settings for Lettering
Small text is one of the trickiest areas in machine embroidery, and underlay choices have an outsized effect on legibility. For letters taller than 10 mm, a center run plus edge walk combination keeps columns crisp without adding so much bulk that the letter strokes look fat.
For letters between 6 mm and 10 mm, a single center run is usually sufficient. Below 6 mm, underlay can actually hurt legibility by adding thread bulk in a very small space — consider reducing underlay density or removing it entirely and relying on a firm stabilizer instead. When you are working with a design file in PES for Brother machines or JEF for Janome machines, check whether the digitizer has already included underlay before adding more in your editing software.
Underlay Angle and Density Settings
Most digitizing software lets you set the underlay angle independently from the top stitch angle. The standard recommendation is to run underlay at 90 degrees to the top stitches, or at 45 degrees if the top fill is already running at 45 degrees. This perpendicular relationship means the underlay threads cross the top threads rather than running parallel, which creates a more stable grid.
Density for fill underlay is typically set lower than the top fill — somewhere around half the density of the final layer. If your software shows density as a spacing value in millimeters, a larger number means fewer stitches per area, so increase the spacing number to reduce density. Getting this balance right prevents the design from becoming stiff or raised in a way that looks unnatural.
Adjusting Underlay in Common File Formats
If you are editing a design file rather than digitizing from scratch, your options depend on the software you use. Programs like Wilcom, Hatch, Embrilliance, and Brother PE-Design all allow you to select individual elements and change underlay type and density without redoing the whole design.
When you open a DST or EXP file, underlay stitches are already baked into the stitch data and cannot be separated from the top stitches without re-digitizing. For this reason, formats that retain object data — such as the native formats of Wilcom or Hatch — are much easier to edit. If you need guidance on which file format works best for your machine, the EmbroideryGo help center covers format compatibility in detail.
For HUS files used on Husqvarna Viking machines and SEW files used on older Pfaff machines, the same principle applies: object-based formats give you editing flexibility, while stitch-only formats lock the underlay in place.
Testing and Troubleshooting Underlay Problems
Always stitch a test on the same fabric and stabilizer combination you plan to use for the final project. A test on scrap cotton tells you nothing useful if the real project is on a fleece jacket. Mark the test piece with the underlay type and density settings so you can refer back to it later.
Common problems and their likely causes: if the top fill looks uneven or gappy, the underlay density may be too low or the angle may be parallel to the top stitches rather than perpendicular. If the design feels stiff and cardboard-like, the underlay is too dense — reduce it by increasing the spacing value. If edges look ragged or satin stitches are rolling off the border, add an edge walk underlay. If the fabric is puckering despite underlay, check that your stabilizer choice matches the fabric weight and that your hoop tension is firm but not stretched.
For more troubleshooting tips and technique articles, visit the EmbroideryGo blog, where new guides are added regularly to help you get the best results from every design you stitch.
Putting It All Together
Underlay is not a one-size-fits-all setting, and experienced embroiderers treat it as a design decision rather than a default checkbox. Start with the fabric type, consider the size and complexity of the design, choose an underlay type that addresses the specific challenge, and always test before committing to the final piece.
Once you develop a feel for how different underlay combinations behave on the fabrics you use most often, you will find that your finished embroidery looks noticeably cleaner, sits flatter, and holds up better through washing. That improvement comes entirely from what the customer never sees — the hidden foundation layer working quietly beneath every stitch.



